F. Willich WILLPOX LC Epoxy - One component 20 kg UV & LED chemistry
    search
    • F. Willich WILLPOX LC Epoxy - One component 20 kg UV & LED chemistry
    • F. Willich WILLPOX LC Epoxy - One component 20 kg UV & LED chemistry
    • F. Willich WILLPOX LC Epoxy - One component 20 kg UV & LED chemistry
    • F. Willich WILLPOX LC Epoxy - One component 20 kg UV & LED chemistry

    F. Willich WILLPOX LC Epoxy - One component 20 kg UV & LED chemistry

    4,500.00
    VAT excluded
    MSRP: 4,730.00

    3 good reasons to use WILLPOX LC:

    • Fully cured system, where light source starts the exothermic process in the epoxy which ensures a strong adhesion between line and pipe
    • Can be used together with glass liner, needle felt liner and BRAWOLINER
    • Fast curing with a pulling speed of up to 1.9 m/min


    Epoxy material can be applied at the workshop and stored for min. 72 hours before installation.

    Quantity
    Out-of-Stock

    The styrene-free WILLPOX® epoxy is also sold as a base material for BRAWOLINER in a private label product under the name BRAVO UVPox.


    Light spectrum:

    LED & UV light sources can be used for curing WILLPOX LC with a wavelength / spectrum in the range 360 nm - 450 nm.


    Pull cable speed:

    The LED & UV light source in the liner is dependent on the power of the light source, dimension of the liner and transmission of light. 


    Here is a table of pull cable speeds for specially developed UV felt liners from lineTEC:

    lineTEC ProFlex S+UV 

    Pull cable speed

    in m/min. 

    WILLPOX LC

    kg/m

    Closed shot
    300/400W

    Open shot
    300/400W

    Closed shot
    600W
    Open shot
    600W
    Closed shot
    1200W
    Open shotd
    1200W
    DN 1001,50,60,4>1,0>1,0--
    DN 1251,80,50,3>1,0>1,0--
    DN 1502,30,40,21,00,81,9>1,0
    DN 2003,0--0,90,71,8>1,0

    I.e. in a liner DN150 mm, where a light source of 1200 W is used, can be pulled in a closed shot at 1.9 mtr/min.



    lineTEC ProFlex +UV 

    Pull cable speed

    in m/min. 

    WILLPOX LC

    kg/m

    Closed shot
    300/400W
    Open shot
    300/400W
    Closed shot
    600W
    Open shot
    600W
    Closed shot
    1200W
    Open shot
    1200W
    DN 1001,360,60,40,80>1,0
    DN 1251,640,50,30,80>1,0
    DN 1502,090,40,20,950,851,9>1,0
    DN 2002,73--0,900,801,8>1,0

    I.e. in a liner DN150 mm, where a light source of 1200 W is used, can be pulled in a closed shot at 1.9 mtr/min.


    Below is a table of pull cable speeds for a typical normal felt liner:

    lineTEC ProFlex 

    Pull cable speed

    in m/min. 

    WILLPOX LC

    kg/m

    Closed shot
    300/400W
    Open shot
    300/400W
    Closed shot
    600W
    Open shot
    600W
    Closed shot
    1200W
    Open shot
    1200W
    DN 1001,360,300,100,800,60--
    DN 1251,640,20-0,650,45--
    DN 1502,09--0,500,300,80,6
    DN 2002,73--0,400,200,60,4

    I.e in a liner DN150 mm, where a light source of 1200 W is used, can be pulled in a closed shot at 0.8 mtr/min.


    WILLPOX LC process instruction:

    1. WILLPOX® is a one-component hybrid resin based on epoxy.

    2. WILLPOX® is homogeneous and must not be stirred before use.

    3. Fyld WILLPOX® LC i den vacuum sugede liner og fordel den med en kalibreringsrulle i henhold til den konfigurerede vægtykkelse.

    4. Temperaturen på WILLPOX® LC skal være min 15°C men det er nemmere at påføre hvis temperaturen ligger mellem 20°C til 23°C.

    5. When the stocking is inverted, it is important that the pipe lining is in contact with the old pipe and that no air pockets can form between the pipe lining and the old pipe.

    6. The reaction is started by the light rays. The exothermic reaction of the resin develops heat and is delayed in relation to the movement of the light source.

    7. Temperatures of up to 130°C can occur during the exothermic reaction, so it is important to allow pressure to remain in the liner after the light source has passed through until the material has cooled below 30°C. Usually approx. 30 minutes.


    121101080

    Data sheet

    Product classification
    Chemistry Epoxy UV - 1K component
    Misc.
    Styrene-free and low odour
    Weight
    20 kg
    Viscosity
    8.000-10.000 mPas
    Color
    Transparant
    E-Module
    3400 MPa
    Light Spectrum
    Wavelength 360 nm - 450 nm
    New product

    You might also like

    Comments (0)
    No customer reviews for the moment.